A beautifully painted commander that rattles loose in a carry case is still a problem. When choosing magnetic bases versus slotted bases, the real question is not which option is universally better. It is which one supports the miniature, game system, movement method and transport routine you actually use.
For a single RPG hero posed on a rocky outcrop, a slotted base may be the quickest route from sprue to table. For a skirmish force that travels in a steel-lined case every week, magnetic basing can save a great deal of repair work. The best choice begins with understanding what each base is designed to do.
Magnetic bases versus slotted bases: the practical difference
A slotted base has a narrow opening designed to accept a miniature’s tab. The tab slots into place, is glued from beneath, and becomes part of the model’s structural connection to its base. This is the familiar arrangement on many plastic, metal and resin miniatures, especially older kits and characterful sculpts made with integral tabs.
A magnetic base can mean two slightly different things. Most commonly, it means an ordinary base fitted with a small neodymium magnet underneath, allowing it to grip a ferrous movement tray or steel-lined storage case. It can also describe a basing system where the miniature itself is magnetised to a base, letting you swap one model between display plinths, scenic inserts or game-specific base sizes.
These approaches solve different problems. A slot secures the miniature to the base. A magnet secures the base, or occasionally the miniature, to another surface. Plenty of hobbyists use both: a slotted base for construction and a magnet beneath it for transport.
When slotted bases make the most sense
Slotted bases are often the straightforward answer when a miniature arrives with a tab. They give the tab a fixed mechanical anchor, which is especially useful for narrow-legged infantry, dramatic running poses and heavier metal miniatures. Instead of relying entirely on glue against two tiny feet, the model has a substantial connection hidden below the base surface.
They are also forgiving during assembly. Test-fit the tab first, widen the slot carefully if the cast demands it, then use a suitable adhesive. Once the joint has cured, the miniature is much less likely to twist off its footing during normal gaming. For a rank-and-file unit with consistent tabs, this is fast, reliable work.
The trade-off is visual freedom. A slot dictates the model’s position and facing unless you cut away the tab and rebuild the attachment points. It can also complicate scenic basing. If you want a trooper standing halfway up a ruined wall, ankle-deep in swamp water or balanced on a discarded mech component, the pre-set tab may fight the composition.
There is also the slot itself to consider. Leaving it exposed looks unfinished, while filling it after the miniature is attached can be awkward. Texture paste, basing grit, putty and carefully placed terrain details all solve the problem, but they add another stage to the build.
Choose slotted bases for secure, conventional assembly
Slotted bases suit models with purpose-made tabs, armies that need quick and repeatable preparation, and miniatures whose pose already works well on a flat gaming base. They are particularly sensible when durability matters more than changing the model’s placement later.
If you are building a large force for regular play, consistency has value. The same base size, the same assembly method and a cleanly finished slot make it easier to organise units, build movement trays and maintain a coherent army appearance.
Where magnetic basing earns its place
Magnetic basing shines once miniatures leave the gaming table. A magnet fitted into the underside of every base lets models adhere to a steel sheet, metal storage box or compatible movement tray. That means fewer foam rub marks, fewer snapped weapons and less chance of a carefully painted centrepiece colliding with the rest of the force during travel.
For tabletop players who transport several squads, this is usually magnetic basing’s greatest advantage. Models remain upright and spaced apart instead of pressing against one another. You can lift a full tray from a case to the table, then return it after the game with far less handling.
Magnets also support flexible unit organisation. A magnetic movement tray can hold a regiment in precise formation without permanently fixing models to it. Remove casualties as needed, shift a character between units, or use the same models in skirmish and mass-battle games. For multi-system collections, that flexibility is useful.
The caveat is that magnet strength must match the miniature. A tiny disc magnet may hold a light infantry model perfectly yet fail under a broad-winged daemon, resin battle mech or heavily scenic cavalry base. Bigger is not automatically better, either. A very strong magnet can make models difficult to remove from a tray and may pull apart poorly glued scenic elements if you lift the figure by the model rather than the base.
Polarity matters as well. Fit every magnet in the same orientation before gluing. One reversed magnet in a twenty-model squad is a small mistake with an irritating result. Set up a master magnet, mark the outward-facing side, and check each piece before adhesive touches plastic or resin.
Magnetic bases need a matching storage plan
Magnets are only as useful as the surface they attach to. A plastic carry case will not hold them. You need a ferrous sheet, a purpose-built magnetic tray or another steel-compatible solution. Avoid assuming that any shiny metal is suitable: some alloys and aluminium surfaces are not magnetic.
A recessed magnet is usually preferable because it sits flush with the underside of the base. If the base has no recess, a magnet can be glued beneath it, but this may make the model sit proud of the table or wobble on textured boards. For gaming pieces, a stable footprint matters more than saving a few minutes in the assembly stage.
Stability, posing and scenic work
The miniature’s pose should influence the decision as much as transport does. A model with one foot planted and a long weapon extending sideways has a high risk of being knocked over. A slotted tab offers a strong anchor, but a magnet beneath the base can add useful resistance against accidental movement on a metal tray.
For scenic bases, magnetic attachment between model and base is often the most adaptable option. Pin the miniature through a foot or scenic contact point, add a magnet or metal pin arrangement, and keep the connection concealed beneath rubble, grass or water effects. This makes painting easier, allows the character to move between bases, and gives display projects more options.
That freedom comes at a cost. A removable join needs careful engineering. The model must sit level, resist rotation and tolerate repeated removal. On a delicate resin miniature, drilling too aggressively can crack thin ankles or damage a detailed cloak. If the model will live on one base for its entire gaming career, a permanent pin-and-glue connection may be the wiser choice.
A sensible hybrid for most collections
For many gaming miniatures, the strongest solution is not a contest between methods. Use the slotted base supplied with the model when the tab provides a good structural fit, finish the base as normal, then install a recessed magnet underneath for storage and movement trays. You gain dependable assembly and safer transport without forcing an unnecessary conversion.
For tabless resin miniatures, attach the feet with pins where possible, build the scenic base around the contact points, and magnetise the underside. Pinning is especially worthwhile for large figures, awkward poses and pieces likely to be handled often. Superglue can hold a surprising amount, but a pin gives the joint something physical to resist shear force.
Check base dimensions before committing. Game systems can be particular about base sizes, and a beautiful scenic base is no help if it makes the model too wide to rank up or obscures important game information. Keep the rim clear where practical, especially if you use colour coding, unit markings or movement trays.
Choose for the miniature’s real job
Use slotted bases when the miniature has a tab, its intended pose works, and you want a dependable permanent build. Use magnetic basing when transport, removable movement trays or flexible display arrangements are central to your collection. Combine them when you want the security of a tab and the convenience of organised, damage-resistant storage.
Before assembling the next squad, place one finished test model in the case, on the tray and beside the rest of the unit. That small trial will tell you more than any universal rule: the right base is the one that keeps your painted force upright, usable and ready for its next campaign.